Tag: diy

repainting insulated metal panels

Can Insulated Metal Panels Be Repainted?

Posted on by

Insulated metal panels come in a wide variety of options. And lucky for us, the majority of insulated metal panels come pre-finished. You may have even been told that these surfaces never need to be painted again! While the factory coatings on these surfaces are durable, nothing lasts forever. Over time, they can chalk and erode, leading to fading of color and a loss of gloss. In extreme cases, the underlying metal can be exposed and rusting may occur. Begging the question…can insulated metal panels be repainted?

Repainting Insulated Metal Panels

That’s right! Insulated metal panels can indeed be repainted and restored back to their former glory. It just takes a little work:

  • Surface Preparation: As with all exterior projects, proper surface preparation is paramount. Begin by thoroughly cleaning your metal panels of all loose dirt, chalk, and other contaminants. This can be done by hand washing with warm, soapy water or with the use of a high-pressure washer. 
  • Apply The Paint: There are many different types of factory applied coatings used on metal panels. Most wear down to a surface that will allow repaint coatings to adhere to the surface. A test patch is recommended before applying your paint to the entire surface. You can use acrylic latex paint or oil-based alkyd paint; just make sure you buy one that is specifically designed to paint a metal panel. 
  • Pro Tips: Sometimes you may need to prime the surface, which will ensure that rust will not creep through and that the paint will stick. You may need a roller designed for corrugated panels, or to make things easy an airless paint sprayer will apply a clean, even coating of paint along the entire surface. A sprayer will also get the job done in a fraction of the time and use less paint as well.

Now that you have all of the information you need, it’s time to begin the painting process. Either hire a professional to help you out or grab a friend and the necessary supplies, and you can get started. 

Need more guidance when it comes to your metal panels? Our qualified team of professionals would be happy to help you along the way! Contact us today at 519-451-7663 or info@ecoinsulatedpanels.com.

Repairing Holes Metal Roof

Can Holes Be Repaired In Metal Roofing Systems?

Posted on by
Repairing Holes Metal Roof

When they are properly installed, metal roofs boast the longest lifespan of any roofing material on the market. While most roofs may last up to 30 years, metal roofs can last up to 100! But longevity is not to be mistaken with indestructibility. Harsh weather conditions, much like the kind we experience in Canada, can take its toll on even the strongest roof. So what do you do when that toll results in one, or several, holes on your metal roof? Let’s talk about how holes can be repaired in metal roofing systems!

Can Holes Be Repaired In Metal Roofing Systems?

The short answer – yes! The longer answer is that how successful that repair is ultimately depends on a couple factors.

  • The material used to patch the hole should be as close to the original material as possible to ensure similar expansion and contraction rates. This will help prevent stressing the patch area.
  • The weather the day of can also result in contraction and expansion of the patch area. This can result in splitting, cracking, and eventually, failure of the repair. 

How To Repair Holes In Metal Roofs

Whether you’re a DIYer or simply interested in the process, this is how we would recommend repairing a hole in your metal roof.

  1. Clean The Repair Area. Before beginning any metal roofing repair project, the repair area must be thoroughly cleaned, including the surface and the surrounding areas. If the hole in your roof was caused by rust, the, rust must be removed entirely. Alternatively, fallen branches or trees may be the cause of the damage. No matter how the damage occurred, it must be cleaned off entirely before repair can occur. 
  2. Scuff The Metal. Once the metal is clean, a wire brush should be used to scuff the repair area. These scuffs will help the sealant bond fully to the metal of the repair area.
  3. Measure Repair Area & Cut Material. After measuring the repair area, cut the panel at least 2 inches past the edges of the repair area. Once it has been cut and fit, round the edges to prevent sharp corners from catching snow or ice. 
  4. Install The Patch For Repair. Using a color-matched urethane sealant, apply the metal patch to the area that needs repair. Don’t be shy! You want to avoid gaps around the patch. Then, firmly press the patch over the damaged areas until the sealant squeezes from the edges of the patch.
  5. Fully Secure The Patch. Once the patch has been put in place, use pan-head sheet metal screws to fully secure the patch to the roof. Lastly, use a putty knife to remove any sealant coming from the edge of the patch. Note, it typically takes a week for the sealant to cure entirely.

Need to repair your metal roof? Contact us at info@ecoinsulatedpanels.com or 1.855.838.9393 to see if we have a panel that’s right for you.

Can Metal Panels Be Painted?

Can Metal Panels Be Painted?

Posted on by

Most metal panels these days come pre-finished. And many of us have been told that these surfaces never need to be painted. Although the factory coatings on these surfaces are typically very hard, they can chalk and erode, leading to fading of color and a loss of gloss over time. In extreme cases, the underlying metal can be exposed and rusting may occur. If your metal panel is in need of some retouching, Insulated Eco Panels has the solution.

Surface Preparation

As with all exterior projects, proper surface preparation is paramount. Begin by thoroughly cleaning your metal panels of all loose dirt, chalk, and other contaminants. This can be done by hand washing with warm, soapy water or with the use of a high-pressure washer. 

Apply The Paint

There are many different types of factory applied coatings used on metal panels. Most generally wear down to a surface that will allow repaint coatings to adhere to the surface. A test patch is recommended before applying your paint to the entire surface.

You can use acrylic latex paint or oil-based alkyd paint; just make sure you buy one that is specifically designed to paint a metal panel. Sometimes you may need to prime the surface, which will ensure that rust will not creep through and that the paint will stick. 

You may need a roller designed for corrugated panels, or to make things easy an airless paint sprayer will apply a clean, even coating of paint along the entire surface. A sprayer will also get the job done in a fraction of the time and use less paint as well.

Now that you have all of the information you need, it’s time to begin the painting process. Either hire a professional to help you out or grab a friend and the necessary supplies, and you can get started. Need more guidance when it comes to your metal panels? Our qualified team of professionals would be happy to help you along the way! Contact us today at 519-451-7663 or info@ecoinsulatedpanels.com.